Plumbing Basics-Plumber's Essentials: Your Key to-What You Need for Bathtub Installation-Installing a Bathtub

At This Website

We have found this article involving Installing A Bathtub below on the net and reckoned it made good sense to discuss it with you on this site.


Installing A Bathtub
Mounting a bath tub isn't specifically rocket science, but it does require solid plumbing, woodworking, and occasionally, tiling abilities. Changing an old bathtub with a new one is additionally a moderately hard project. If the old tub is readily accessible, the job can relocate easily; if you need to open a wall to get rid of the old tub and position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. Ensure you have qualified yourself for the job as well as are comfortable trying it. Instead of hiring a service provider to take control of a halfway-completed task, it is far better to consider using one before you start. Opportunities are you might require a specialist plumber to make tube links.
This short article will certainly aid you mount a new bathtub in your bathroom if you have currently acquired a new bathtub and do not require to change the arrangement of your previous water pipelines.
Your tools and product list should comprise the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water. After doing so, activate the faucets to drain any water remaining in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted access that is often the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have actually been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned up of any old securing compound.
    Before carrying on to fit the brand-new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end gives a link to the existent supply pipelines.
    If you require to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
    Next off, position the tap in the installing opening in the bath/basin making certain that the washers remain in area in between the faucet and the sink. Safeguard the faucet in position with the maker supplied backnut. Once the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The former kind ought to be connected to the tap finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Installing the Bath tub


    Utilizing the two wood boards under its feet, put the tub in the required position. The wood boards are helpful in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four tiny points.
    The following goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the level and adjusting the feet on the bath tub until the spirit level checks out level.
    To set up faucets, fit all-time low of the furthest versatile faucet connector to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
    Activate the water system and also inspect all joints and new pipework for leaks as well as tighten them if required. Load the bath tub and additionally examine the overflow outlet and the regular electrical outlet for leaks.
    Finally, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub needs to wait until the bathtub has actually been used at the very least when as this will settle it right into its final placement.

    Preparing for the Installment


    First of all, the sustaining framework supplied with the bathroom should be fitted (if needed) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps system to prevent pressure on the tub.
    Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the supplied washers.
    Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last setting.

    Tiling Around the Bath tub


    In the location where the bathroom meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break an inflexible seal, triggering the water to pass through the wall surface in between the bathroom and the tiling, leading to difficulties with wetness and also feasible leakages to the ceiling listed below.
    You can select from a range of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, and also can securing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always load the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealer can fracture relatively early if you do not consider this activity prior to securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently available on the market. It is suggested to fit the tiles using waterproof or water-proof sticky as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    As a devoted person who reads about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that blog post was really helpful. Those who liked our blog post please make sure you remember to pass it around. Many thanks for taking the time to read it.


    Certified experts available.

    Leave a Reply

    Your email address will not be published. Required fields are marked *